This information is for the following models:
About this download
Thank you for your continued interest in Sony products.
Sony is offering a firmware upgrade program for Interchangeable Lens Digital Camera SLT-A99.
Improvements after firmware upgrade
- Provides support for the Dual AF function compliant lens: SAL50F14Z
- Addition of HDMI simultaneous output mode
In addition to the existing HDMI simultaneous output during movie recording, the camera will be able to display smooth smooth 60fps(NTSC)/50fps(PAL) video on an external monitor connected via HDMI and on the LCD screen of the camera simultaneously also during movie recording standby.
Note: The camera needs to be in Movie mode with [HDMI Info. Display] set to [Off].
Improvements from firmware version 1.00 to version 1.01
- Expanded the number of Dual AF function compliant lenses:
SAL24F20Z, SAL85F14Z, SAL135F18Z, SAL70300G, SAL70200G,
SAL35F14G, SAL1635Z, SAL100M28, SAL50M28, SAL85F28, SAL300F28G, SAL70400G2
- Expanded the number of automatic compensation compliant lenses:
SAL100M28, SAL50M28, SAL85F28, SAL18200, SAL20F28, SAL28F28
Applicable firmware version
- The applicable products are with the firmware Version 1.01 or earlier..
How to check the firmware version
- Select Menu → Setup → Version on the camera.
- The firmware version is displayed.
If your camera firmware version is already Version 1.02, this update is not necessary.
- Windows 10
- Windows 8.1
- Windows 7 SP1
Other system requirements
- Hard disk space: 200MB or more
- RAM: 512MB or more
Note: Please close all other application software before upgrading the firmware.
- USB cable supplied with the camera
Note: Update functionality is not guaranteed with any other USB cable.
- Power source for the camera
Fully charged rechargeable battery pack NP-FM500H or AC adaptor AC-PW10AM (sold separately).
Note: The upgrade can be performed only when the remaining battery level is (three marks) or more. We recommend that you use a fully charged battery or the AC adaptor AC-PW10AM (sold separately).
- Windows 10
- Windows 7
- Windows 8 32bit
- Windows 8 64bit
- When performing the firmware upgrade, please use a fully charged rechargeable battery pack NP-FM500H or the AC adaptor AC-PW10AM (sold separately).
- Do not remove the battery or AC adaptor during the upgrade; otherwise, the camera may become inoperable due to the sudden power shutdown.
- Remove the memory card from the camera beforehand.
- Do not cover Eyepiece sensors during the update; otherwise, the LCD monitor may switch to the Viewfinder. If you can not see anything on the LCD monitor, please press FINDER/LCD button.
Updating the Firmware
- Download the upgrade file.
Click on Update_SLTA99V102.exe to begin download.
Please save the downloaded file onto the Desktop of your computer (recommended).
For Windows 8 users:
Under the initial settings of Internet Explorer, the update file will be saved in the Downloads folder. Click the Desktop tile from the Start screen and find the downloaded file in the Downloads folder by using Explorer.
- Start up Firmware Updater.
- Close all currently running programs on your computer.
- Double-click the downloaded file Update_SLTA99V102.exe.
- Firmware Updater starts up.
- Check the USB connection mode.
According to the instruction on Firmware Updater, select Menu → Setup → USB Connection on the camera, and confirm Mass Storage is selected.
If the mode other than Mass Storage is selected, please select Mass Storage.
- Connect the camera to the computer with the supplied USB cable.
USB Mode appears on the LCD monitor of the camera.
If the computer cannot find the camera, the message Could not find the camera for this update. appears on the computer display. Try the following if this happens.
- Disconnect the USB cable and connect it again.
- If the computer has multiple USB terminals, try with the other terminals.
(Your computer may have some USB terminals on the backside.)
Sometimes when the camera is connected to the computer with the USB cable, the message to encourage rebooting the computer may appear on the computer display. In this case, remove the battery pack or AC adaptor from the camera, reboot the computer, and follow the procedures from Start up Firmware Updater.
- Confirm is displayed on the task tray at the lower right corner of the computer screen.
- After confirming the above, click Next on Firmware Updater.
Do not cover Eyepiece sensors during the update; otherwise, the LCD monitor may switch to the Viewfinder. If you can not see anything on the LCD monitor, please press FINDER/LCD button
This screen appears on Firmware Updater
This screen appears on the LCD screen of the camera.
Note: From this step onwards, never turn off the camera until the firmware upgrade is completed.
- After confirming the screens on Firmware Updater and LCD screen, click Next. The current version and the version after the upgrade appear on the lower left part of the Firmware Updater.
Upgrade is required
Upgrade is not required
Note: If the screen below appears, the upgrade is not required. According to the message, stop the USB connection and click Finish. Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.
- Click on the task tray at the lower right corner of the computer screen to stop the USB connection.
Note: Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.
- Press the center of the multi-selector (the control button) to execute.
Camera’s LCD screen
Camera control wheel
Note: The screen turns off when the center of the control wheel is pressed. Please proceed to the next step.
- After resetting, reconnection of the camera is verified.
Click Run to start the upgrade. The progress bar appears while upgrading (approximately 10 minutes).
Note: Never turn off the camera nor disconnect the USB cable while upgrading.
- When the upgrade is completed, click Finish and disconnect the USB cable.
- Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.
Check the firmware version
Follow the instruction below to confirm the firmware version.
- Select Menu → Setup → Version on the camera.
- The firmware version is displayed. The firmware upgrade was completed successfully if Ver.1.02 is displayed.